Shale shaker GNPS70-3S is high efficiency BEM shale shaker. It is designed according to users’ actual demand based on modern technique and principle. GNPS70-3S takes advantage of double vibration motors in-phase principle. It holding ideal design on structure, and work steadily, operated lasting time without any problem, take rather little cost on maintenance.
If choose proper model or parameters, it can work for many kinds of drilling fluid solids control. It is an ideal solution for Oil and gas drilling, HDD mud recycling, Metallurgy, mining tail mud solids control
GNPS70-3S Shale shaker structure
Please find GNPS70-3S shaker structure as fig I. It contains pedestal, shaker deck, tension wedge, shaker screen, rubber strip, deck adjustment device, baffle box, tension device, electric cabinet, vibration motor, damping spring.
Shale shaker GNPS70-3S can be used by single or designed as tandem and triplex shaker to be operated at drilling job site
GNPS70-3S Shale shaker technical parameters
Vibration: Balanced elliptical motion
Vibration amplitude: 7mm (double type)
Motor power: 2.2+1.1KW
Treating capacity: 60L/S
Screen area: 2.2m2
Shaker screens: 700x1050mm x 3 10~200 mesh (Frame screen or Pyramid frame screen)
1. GNPS70-3S Shale shaker is designed as double motors in-phase principle. The shale shaker will vibrate as elliptical, part of spare parts are interchangeable with international shale shaker
2. Adopts advanced vibration motor, reliable operation, run long time without any problem
3. The shaker screen can be flat type or pyramid type. Shaker deck can fix 3 pieces screen and make screens as different combination.
This will lead screen take longest usable life. According to different drilling mud the screen mesh will be 40-200 mesh
4. Screen is tensioned by wedge, this is more convenient and reliable
5. The shale shaker deck can be adjusted. Adjustment will be realized by adjusting worm whirl. There is worm whirl at each side of shaker deck. Middle shaft connect two whirl pipe, when we make adjustment, two sides will be compliant and in-phase
6. The paint of shaker is processed by grit blast, use high anticorrosive zinc rich coating. Will make shaker surface anticorrosive and more beautiful
Main operations on GNPS70-3S
1. Shaker screen selection
GNPS70-3S shale shaker can fix different meshes screen. This equipment can use 10-200mesh screen. Usually, when the shale shaker is first stage solids control equipment the shaker screen can be 30-100mesh. When the shale shaker is a part of mud cleaner, the screen can be 80-200mesh.
Shaker screen selection can among manufacturer engineer, user, and contractor discussion. Replacement screen should be selected specially from manufacturer
2. Replace shaker screen process
To make screen installation and uninstall more easy, GNPS70-3S designed fast installation structure. The structure is a special type use tension wedge to fix screen. Refer to fig IV. The structure including shelve strip, wedge. The first screen installation, we should inspect the screen dimension, such as 1050+/-2mm, the tolerance can’t over it.
After fixed rubber strip, then put screen, shelve strip from shaker back (drilling fluid input), and push wedge evenly on two sides use hammer to push or tension wedges, make two sides identical. Tension each screens subsequently.
Shale shaker screen replacement, during operation, when screens broken or need to be replaced , please refer to fig IV. Get wedge out, then bring out screen, check if rubber strips are sufficient; then put new screen on shaker deck and tension it steadily. The replacement is finished
3. Shaker deck angle adjustment
Shaker deck angle adjustment refer to fig V. There is mainly bracket, pedestal, elevation whirl worm, elevation nuts, etc. When we make adjustment, handle wheel rotary by clockwise, shaker deck angle will be larger; handle wheel rotary by anti clockwise shaker deck angle will be less.
Shale shaker output angle adjustment can be operated under running and off. When finish the shaker deliver it, the shaker deck is 0°.
When user operate shaker, according to drilling mud property and flow rate on job site, and adopts same screen, the angle is higher, the treating performance will be better while treating capacity will be higher. When drilling fluid is leaking on shaker deck, increase deck angle can get rid of fluid flow away
GNPS70-3S for GNPJ70-3 mud cleaner
GNPJ70-3 combined GNPS70-3S, Desander cone, Desilter cones as well. Thanks to the BEM vibration type make this mud cleaner more effecient. If the two equipments configured in one system, this will save much time and provide more convenience on spare parts replacement, such as shaker screen, etc.
This type shaker and mud cleaner provides users ideal solution and economical cost. It will save drilling cost or decrease more investment also
Try to get more information please contact GN or browse the website
No related posts.
Related posts brought to you by Yet Another Related Posts Plugin.